Machine Tools from L & W

Specification

ITEMS	CiNCh-Mill 18	CiNCh-Mill 20	CiNCh-Mill 25
TABLE
Worktable	355x1270mm 14"x50"	406x1372mm 16"x54"	420x1600mm 16.5"x63"
T-slot	16x3x64mm	16x3x64mm	16x5x60mm
Table load capacity	500 kgs	600 kgs	800 kgs
3 AXES
X axis travel	800mm	1000 mm	1300 m/m
Y axis travel	400mm	500mm	635 m/m
Z axis travel	450mm	520mm	620 m/m
Feed Rate	0-5 M/min	0-5 M/min	0-5 M/min
Rapid travel	0-10 M/min	0-10 M/min (0-20 M/min opt.)	0-10 M/min (0-20 M/min opt.)
Ballscrew diameter	Ø32mm	Ø32mm	Ø40mm
Guideway	X: Dove tail, Y/Z: box way
Transmission	belt drive	belt drive	belt drive
SPINDLE
Spindle taper	BT-40 (CAT-4O)	BT-40 (CAT-10)	BT-40 (CAT-40)
Spindle speed	6000 r.p.m.	6000 r.p.m.	6000 r.p.m.
Spindle motor	7.5 HP	10 HP	10 HP
GENERAL
N.W.	2500 kgs	3100 kgs	3800 kgs
G.W.	3000 kgs	3500 kgs	4200 kgs
Packing measurement (LxWxH) (cm)	210x228x225	290x228x255	Machine/ 330x228x255 Guarding/ 110x228x180

ITEMS	CiNCh-Mill 30	CiNCh-Mill 30S	CiNCh-Mill 30SB (BOX WAY)
TABLE
Worktable	450x1800mm 17"x70"	610x854mm 24"x73"	610x1854mm 24"x73"
T-slot	16x5x60mm	18x5x70mm	18x5x100mm
Table load capacity	1000 kgs	1500 kgs	1000 kgs
3 AXES
X axis travel	1500 mm	1500 mm	1500mm
Y axis travel	650 mm	870 mm	800mm
Z axis travel	620 mm	710 mm	700mm
Feed Rate	0-5 M/min	0-5 M/min	0-5 M/min
Rapid travel	0-10 M/min (0-20 M/min opt.)	0-10 M/min (0-20 M/min opt.)	0-10 M/min (0-20 M/min opt.)
Ballscrew diameter	Ø40mm	Ø40mm	Ø40mm
Guideway	X: Dove tail, Y/Z: box way		X/Y/Z: box way
Transmission	belt drive	belt drive	direct mounted
SPINDLE
Spindle taper	BT-40 (CAT-4O)	BT-40 (CAT-10)	BT-40 (CAT-40)
Spindle speed	6000 r.p.m.	6000 r.p.m.	6000 r.p.m.
Spindle motor	10 HP	15 HP	15 HP
GENERAL
N.W.	4000 kgs	5600 kgs	4800 kgs
G.W.	4400 kgs	6100 kgs	5400 kgs
Packing measurement (LxWxH) (cm)	Machine/ 330x228x255 Guarding/ 110x228x180	Machine/ 354x228x255 Guarding/ 230x228x180	Machine/ 350x228x256

ITEMS	CiNCh-Mill 40	CiNCh-Mill 50
TABLE
Worktable	762x1830mm 30"x72"	813x2185mm 32"x86"
T-slot	18x5x100mm	18x5x100mm
Table load capacity	1500 kgs	1800 kgs
3 AXES
X axis travel	1700mm	2000 mm
Y axis travel	870mm	870mm
Z axis travel	710mm	710mm
Feed Rate	0-5 M/min	0-5 M/min
Rapid travel	0-10 M/min (0-20 M/min opt.)	0-10 M/min (0-20 M/min opt.)
Ballscrew diameter	Ø40mm (Ø50mm opt.)	Ø40mm (Ø50mm opt.)
Guideway	X: Dove tail, Y/Z: box way.
Transmission	belt drive	belt drive
SPINDLE
Spindle taper	BT-40 (CAT-40)	BT-40 (CAT-40)
Spindle speed	6000 r.p.m.	6000 r.p.m.
Spindle motor	15 HP	15 HP
GENERAL
N.W.	6500 kgs	6600 kgs
G.W.	7000 kgs	7100 kgs
Packing measurement (LxWxH) (cm)	Machine/ 373x240x326 Guarding/ 220x105x200 220x140x120 110x140x120	Machine/ 373x240x330 Guarding/ 220x105x200 220x105x200 110x160x120

Note:

L&W Machine Tools, Inc. reserves the right to alter any mechanical specification without prior notice in the interest of product development.

30s is special-designed of box way on all axes.